FAQ: How To Use A Drain Auger?

Instructions on How to Use a Drain Auger

  1. The first step is to insert the Drain Auger. Drain auger: Take the end of your drain auger and insert it into the drain or directly into your toilet. Step 2: Direct the Drain Auger in the direction of the clog. Step Three: Remove the Drain Auger from the Toilet.
  2. Turn the handle clockwise while you carefully slide the drain snake into the toilet.

What is the difference between a drain snake and an auger?

Drain snakes are useful for cleaning out smaller drains, such as those under your kitchen or bathroom sink. Drain augers are used to clear clogs in bigger pipes, such as your toilet or shower drain. An auger will be used for lines in the 1-1/2′′ – 3′′ range, and a snake will be used for lines in the 1-1/4′′ – 2′′ range. When they do, it’s usually because of roots that have grown into the pipes.

How do drain augers work?

Often referred to as a plumbing auger or plumbing snake, a plumbing auger or plumbing snake is a long, flexible metal cable with a tiny, uncoiled spring at one end and a handle at the other. The auger head on the snake has the appearance of a corkscrew. Using a snake, a plumber may physically contact and take away the obstruction causing the clog by entering the drain directly and exiting the drain.

Is a drain snake easy to use?

Drain snakes are straightforward equipment, but they must be handled correctly in order to make draining a drain a simple operation.

We recommend reading:  FAQ: How To Use Minoxidil For Beard?

What is a drain auger used for?

A plumber’s snake, also known as a drain snake, is a thin, flexible auger that is used to clear obstructions from plumbing systems. The plumber’s snake is frequently used to unclog obstructions that are too tough to be unclogged using a plunger alone. It is also referred to as a toilet jack in some circles.

Should I buy a drain auger?

An item that should be kept on hand in the home is a drain snake, for starters. When dealing with a minor blockage, a basic hand-crank drain snake (also known as a drain auger) is a far superior solution than using chemical drain cleaners. These chemicals should never be used on your drains in the first place!

Can a drain snake break a pipe?

Drain Snakes Have the Potential to Damage Pipes Drain snakes, although being marketed as devices that are simple to use by anybody and everyone, may be difficult to control and, if used incorrectly, can cause damage to pipes. Pipes that are over 100 years old in many homes have been galvanized, or coated with zinc, in order to keep the pipe from corroding or rusting.

How do you unclog a drain if a snake doesn’t work?

Expand the snake cable into the drain a few inches at a time, gradually increasing the length of the snake cable. Once you begin to sense it reaching the blockage, go even more slowly. In order to clear the blockage, the cable must be rotated in order to do so.

How do you unclog a main drain without a snake?

Extend the snake cable into the drain a few inches at a time, gradually increasing the length of the snake cable. Move much more slowly as you begin to sense it reaching the obstruction. Because the cable is being rotated, the blockage will be loosen.

We recommend reading:  Often asked: How To Use An Egg Poacher?

How long of a drain auger do I need?

Because they are intended for the most difficult of clogs, the cable should be no smaller than 5/8 inch in diameter and 75 to 100 feet in length at a minimum. Cleanouts to the street are normally cleaned out with this snake, which is meant to clear out drains that are 3 inches or bigger in diameter.

Is Drano bad for pipes?

Drano® will not do any damage to your pipes or plumbing. It is not need to be concerned since Drano® solutions are powerful enough to dissolve even the most stubborn clogs, yet they will not harm your plastic or metal pipes. All Drano® products are completely safe to use and may be used with either plastic or metal pipes.

Leave a Reply

Your email address will not be published. Required fields are marked *