Readers ask: How To Configure Cisco Air-cap2702i-a-k9?

How do I manually configure a Cisco access point with a controller?

Configure

  1. Have a DHCP server present so that the APs can acquire a network address. Note: Option 43 is used if the APs reside in a different subnet.
  2. Configure the WLC for basic operation.
  3. Configure the switch for the WLC.
  4. Configure the switch for the APs.
  5. Register the lightweight APs to the WLCs.

How do I assign an IP address to a Cisco access point?

My solution was as follows:

  1. Connect console cable from laptop to AP.
  2. Connect Power Injector to POE port of AP.
  3. Connect LAN cable from my laptop’s LAN interface to the Power Injector’s LAN interface.
  4. Configure my laptop’s LAN interface with the IP address of the default gateway that the AP will have.

How do I access Cisco AP?

Open a web browser, and enter the IP address of the AP in the address line. Enter the Username and Password. The default username and password are Cisco.

How do I reset my cisco Air CAP3502I a K9?

Factory reset AIR-CAP3502I-E-K9

  1. Connect to the access point with a serial/console cable, fire up PuTTY and connect to the correct COM port.
  2. Whilst holding the MODE button, connect the power cable or ethernet cable if using PoE.
  3. Keep holdings the MODE button until the LED flashes red.

How do I reset my air cap1702i e K9?

This is important: I press and hold the MODE button for 20s (until the LED become solid RED). While the button is still pressed, I plug the power back in. I now wait for the message “button is pressed, wait for button to be released…“. Let’s release the MODE button and wait for the code to load.

We recommend reading:  FAQ: How To Configure Hsrp On Cisco Switch 3750?

What are the steps to configure an access point?

HOW TO SETUP ACCESS POINT

  1. Step 1:Connect the router to your existing router via an Ethernet cable.
  2. Step 2:Attach the new router’s (to be used as AP) power cable to the rear Power port and wall electrical outlet.
  3. Step 3:Wait until the device initializes.
  4. Step 4:For example, the IP address might be ‘192.168.

What are controller based access points called?

Controller-based Access points are also known as thin clients and require a controller for centralized management (updates, configuration, etc.) and do not need to be manually configured. Generally, Controller based Access points are generally used in large environments.

How do I save my cisco access point?

In the Save Action area, click the Download (PC to AP ) radio button to download the configuration file from the PC to the Access Point.

What is the default IP address for a Cisco access point?

Note: The default IP address of the Access Point is 192.168. 10.10. If no webpage appears, try to reset the IP address.

What is the default password for Cisco access point?

In the absence of a DHCP server, the access point will fallback to the default static IP address after 60 seconds. Step 3. Login with the default credentials. The default username is cisco, and the default password is cisco.

What is an autonomous access point?

First, let’s consider the autonomous access points. Here, each access point is managed individually. They have no direct knowledge of one another, they’re not centrally administered. And that might be fine for a very small installation, but it’s not going to scale well. As a second option, we can have lightweight APs.

We recommend reading:  FAQ: How To Configure Nat In Cisco Router Step By Step?

How do I log into my access point?

Open the web browser and type the IP address of the access point/extender (Default is 192.168. 1.1/ 192.168. 1.254/192.168. 0.254) into the address bar and then Press Enter.

What is AP priming?

Priming is the process where the regulatory domain and country configuration for the universal access point is set. The regulatory domain and country configuration for your access point define the valid set of channels and allowed power levels for the country where your AP is installed.

How do I log into my Cisco Aironet?

CISCO Aironet 1200 Login Guide

  1. Open your web browser (e.g. Chrome, Firefox, Opera or any other browser)
  2. Type 10.10. 10.1 (the default IP to access the admin interface) in the address bar of your internet browser to access the router’s web-based user interface.
  3. The default username for your CISCO Aironet 1200 is Cisco.

Leave a Reply

Your email address will not be published. Required fields are marked *