Quick Answer: How To Configure Cisco Aironet 1260?

How do I manually configure a Cisco access point with a controller?


  1. Have a DHCP server present so that the APs can acquire a network address. Note: Option 43 is used if the APs reside in a different subnet.
  2. Configure the WLC for basic operation.
  3. Configure the switch for the WLC.
  4. Configure the switch for the APs.
  5. Register the lightweight APs to the WLCs.

How do I access my Cisco Aironet 1200?

CISCO Aironet 1200 Login Guide

  1. Open your web browser (e.g. Chrome, Firefox, Opera or any other browser)
  2. Type 10.10. 10.1 (the default IP to access the admin interface) in the address bar of your internet browser to access the router’s web-based user interface.
  3. The default username for your CISCO Aironet 1200 is Cisco.

How do I assign an IP address to a Cisco access point?

My solution was as follows:

  1. Connect console cable from laptop to AP.
  2. Connect Power Injector to POE port of AP.
  3. Connect LAN cable from my laptop’s LAN interface to the Power Injector’s LAN interface.
  4. Configure my laptop’s LAN interface with the IP address of the default gateway that the AP will have.

What is the default IP address for a Cisco access point?

If the wireless access points do not receive a DHCP response (there is no DHCP server on your network) after 60 seconds, the access points will fallback to the following default static IP address: 192.168. 1.245 and a default mask of 255.255. 255.0.

What are the steps to configure an access point?


  1. Step 1:Connect the router to your existing router via an Ethernet cable.
  2. Step 2:Attach the new router’s (to be used as AP) power cable to the rear Power port and wall electrical outlet.
  3. Step 3:Wait until the device initializes.
  4. Step 4:For example, the IP address might be ‘192.168.
We recommend reading:  Quick Answer: Cisco How To Configure Macros?

How do I add a wireless access point to a controller?

From the WLC controller GUI, click Security > AP Policies. and the AP Policies page appears. Click the Add button on the right hand side of the screen. Under Add AP to Authorization List, enter the AP MAC address (NOT the AP Radio mac address).

How do I save my cisco access point?

In the Save Action area, click the Download (PC to AP ) radio button to download the configuration file from the PC to the Access Point.

What are controller based access points called?

Controller-based Access points are also known as thin clients and require a controller for centralized management (updates, configuration, etc.) and do not need to be manually configured. Generally, Controller based Access points are generally used in large environments.

What is the default password for Cisco Aironet AP?

In the absence of a DHCP server, the access point will fallback to the default static IP address after 60 seconds. Step 3. Login with the default credentials. The default username is cisco, and the default password is cisco.

How do I reset my Cisco access point password?

1. Connect to the 1242’s Web interface by directing a Web browser to the access point’s IP address as decided during its setup. Attempt to log in with the default administrator username “Cisco” with the password “Cisco. ” Be sure to capitalize the “C.” If this does not work, the configuration must be reset.

What is an autonomous access point?

First, let’s consider the autonomous access points. Here, each access point is managed individually. They have no direct knowledge of one another, they’re not centrally administered. And that might be fine for a very small installation, but it’s not going to scale well. As a second option, we can have lightweight APs.

We recommend reading:  Quick Answer: How To Configure Firewall Cisco Asa 5505?

How do you get to the console of an access point?

To access the AP console command prompt, press Enter when the AP displays the message “Hit to stop autoboot.” If the autoboot countdown expires before you can interrupt it, turn the device off and then back on.

Leave a Reply

Your email address will not be published. Required fields are marked *