Question: How To Configure Cisco Aironet 1142n?

How do I make my Cisco AP a repeater?

Steps to Configure the AP as Repeater:

  1. Enable Aironet extensions on both the parent and repeater APs. By default, these extensions are enabled.
  2. Setup the SSID under specific Radio {0 or 1}
  3. Assigns the SSID as an infrastructure SSID. This is the SSID the repeater uses to associate to the root AP.

How configure SSID Cisco AP?

Method 2: Configure the SSID on an AP with a CLI

  1. Configure the SSID and map it to a VLAN. Enable. Conf ter. Dot11 ssid Cisco. Vlan 50. Authentication open. Guest-mode.
  2. Configure the Dot11 Radio 0 and Gigabit Ethernet interfaces. >Conf t. interface Dot11Radio 0. ssid Cisco. Exit. Interface Dot11Radio 0.50.

How do I assign an IP address to a Cisco access point?

My solution was as follows:

  1. Connect console cable from laptop to AP.
  2. Connect Power Injector to POE port of AP.
  3. Connect LAN cable from my laptop’s LAN interface to the Power Injector’s LAN interface.
  4. Configure my laptop’s LAN interface with the IP address of the default gateway that the AP will have.

How do I manually configure a Cisco access point with a controller?

Configure

  1. Have a DHCP server present so that the APs can acquire a network address. Note: Option 43 is used if the APs reside in a different subnet.
  2. Configure the WLC for basic operation.
  3. Configure the switch for the WLC.
  4. Configure the switch for the APs.
  5. Register the lightweight APs to the WLCs.

What is the main purpose of configuring an AP as a repeater?

Repeater Overview The repeater forwards traffic between wireless clients and the AP connected to the wired LAN (or other repeaters). APs configured as repeaters do not forward traffic from the Ethernet port (although this might change in future versions of the software).

We recommend reading:  Readers ask: How To Configure Cisco Router 2800 Series Step By Step?

What is a repeater Cisco?

Understanding Repeater Access Points The repeater forwards traffic between wireless users and the wired LAN by sending packets to either another repeater or to an access point connected to the wired LAN. When you configure an access point as a repeater, the access point’s Ethernet port does not forward traffic.

What is the default IP address for a Cisco access point?

Note: The default IP address of the Access Point is 192.168. 10.10. If no webpage appears, try to reset the IP address.

What are the steps to configure an access point?

HOW TO SETUP ACCESS POINT

  1. Step 1:Connect the router to your existing router via an Ethernet cable.
  2. Step 2:Attach the new router’s (to be used as AP) power cable to the rear Power port and wall electrical outlet.
  3. Step 3:Wait until the device initializes.
  4. Step 4:For example, the IP address might be ‘192.168.

How do I log into my Cisco access point?

The default username is Cisco. Step 4 Enter the wireless device password in the Password field and press Enter. The default password is Cisco.

How do I find the IP address of my cisco access point?

To find the Access Point’s IP address

  1. Open utility window, make sure Get IP addr is selected in the Function box.
  2. Type the Access Point’s MAC address in the Device MAC ID field.
  3. Click Get IP Address.
  4. Write down the Access Point’s IP address that appears in the IP Address field.

How do I set a static IP to an access point?

Log in to the access point’s web-based setup page. Launch a web browser and enter the access point’s IP address in the Address bar then press Enter. Step 2: Once the setup page appears, click the Network Setup drop-down and select Static IP.

We recommend reading:  Readers ask: How To Configure Cisco 2960 Switch As Dhcp Server?

How do you get to the console of an access point?

To access the AP console command prompt, press Enter when the AP displays the message “Hit <Enter> to stop autoboot.” If the autoboot countdown expires before you can interrupt it, turn the device off and then back on.

How do I add a wireless access point to a controller?

From the WLC controller GUI, click Security > AP Policies. and the AP Policies page appears. Click the Add button on the right hand side of the screen. Under Add AP to Authorization List, enter the AP MAC address (NOT the AP Radio mac address).

How do I access my Cisco wireless controller?

Both the wired and wireless clients can access the dynamic interface of the controller using the CLI and GUI. To access the GUI of the controller enter the dynamic interface IP address of the controller in the address field of either Internet Explorer or Mozilla Firefox browser.

How do I save my Cisco access point?

In the Save Action area, click the Download (PC to AP ) radio button to download the configuration file from the PC to the Access Point.

Leave a Reply

Your email address will not be published. Required fields are marked *