Question: How To Configure Cisco Air-cap3602i-a-k9?

How do I manually configure a Cisco access point with a controller?

Configure

  1. Have a DHCP server present so that the APs can acquire a network address. Note: Option 43 is used if the APs reside in a different subnet.
  2. Configure the WLC for basic operation.
  3. Configure the switch for the WLC.
  4. Configure the switch for the APs.
  5. Register the lightweight APs to the WLCs.

What is air CAP3602I a K9?

Designed to address the wireless connectivity needs of factories, large office and other indoor industrial environment, AIR-CAP3602I-A-K9 is the enterprise class, three-spatial-stream access point with Dual-band, controller-based 802.11a/g/n, internal antennas and A regulatory domain.

How do I configure a Cisco router as an access point?

Cisco Wireless Access Points – Cisco Workgroup Bridges: Cisco Unified Wireless Network Configuration Example

  1. Enter the SSID name, VLAN ID, and the RADIO interface.
  2. In the Client Authentication Settings area, check the Open Authentication check box.
  3. Leave all other parameters with their default values.
  4. Click Apply.

What are the steps to configure an access point?

HOW TO SETUP ACCESS POINT

  1. Step 1:Connect the router to your existing router via an Ethernet cable.
  2. Step 2:Attach the new router’s (to be used as AP) power cable to the rear Power port and wall electrical outlet.
  3. Step 3:Wait until the device initializes.
  4. Step 4:For example, the IP address might be ‘192.168.

What is the master controller mode on WLC?

Q. When should I use the master controller mode on a WLC? A. When there is a master controller enabled, all newly added access points with no primary, secondary, or tertiary controllers assigned associate with the master controller on the same subnet.

We recommend reading:  How To Configure Vlan Ip Address On Cisco Router?

How do I reset my air cap1702i e K9?

This is important: I press and hold the MODE button for 20s (until the LED become solid RED). While the button is still pressed, I plug the power back in. I now wait for the message “button is pressed, wait for button to be released…“. Let’s release the MODE button and wait for the code to load.

How do I reset my cisco wireless router?

Press the Reset button located at the back of the device with a pin for approximately 15 seconds or until the power light on the front of the device starts flashing. The Router reloads and is set to the default configuration settings. Step 2. Login with the default credentials.

How do I reset my cisco access point to factory settings?

Reset Cisco Wireless AP to factory defaults

  1. Connect the console cable.
  2. Unplug the power or network cable if connected to a POE switch.
  3. Press and hold the Mode button.
  4. Plug the power back into the AP.
  5. Wait until the output on the console says button is pressed.

What is radio type 802.11 N?

802.11n is a specification for wireless LAN (WLAN) communications. 802.11n uses multiple input / multiple output (MIMO) technology and a wider radio frequency channel. It also provides a mechanism called frame aggregation to decrease time between transmissions.

What is Cisco Meraki access point?

The Cisco Meraki MR42 is a four radio, cloud-managed 3×3 MU-MIMO 802.11ac Wave 2 access point. Designed for high-performance, high-density next-generation deployments in offices, schools, hospitals, shops, and hotels, the MR42 offers performance, security, and simple management.

We recommend reading:  Often asked: Cisco 6509 Voice Vlan How To Configure?

How do I configure my router?

Router setup steps

  1. Step 1: Decide where to place the router.
  2. Step 2: Connect to the Internet.
  3. Step 3: Configure the wireless router gateway.
  4. Step 4: Connect gateway to router.
  5. Step 5: Use app or web dashboard.
  6. Step 6: Create a username and password.
  7. Step 7: Update the router’s firmware.
  8. Step 8: Create a Wi-Fi password.

Is a router a WAP?

A router is a network element that deciphers where data packets need to go. In comparison, a WAP is just an alternative to wires that allow computers to connect wirelessly and provides a degree of mobility to the user. A WAP only device cannot act in the same capacity and still needs a router for that purpose.

How do I setup a router as an access point?

Use an Ethernet cable to connect the access point to the router. The cable should be inserted into a LAN port on the router and into the main Ethernet port on the access point. This introduces the access point to the router’s created local area network. Use an Ethernet cable to connect the router to the computer.

Leave a Reply

Your email address will not be published. Required fields are marked *